Okay

Get in Touch

General
(508) 921-4600
Sales@ueidaq.com
Support@ueidaq.com

UEI Europe Office
Salesemea@ueidaq.com

Click here for local offices and distributors.

Find us on WeChat.

UEINet Cube with Simulink

UEINet-SIM

Features

Option configures the UEINet to a Simulink target

UEINet Cube with Simulink
Software/Programming: How UEI solutions are used. Hosted - Connected to a PC with Windows, Linux, QNX, VxWorks, RTX, or similar OS. Hosted also is for OPC-UA, Modbus and EtherCAT. Standalone - Controller with Linux or VxWorks OS, Simulink I/O Target or UEILogger. Available options for this product are shown in the drop down menu.
CPU Configurations:
Solid State Hard Drive:
SD Card:
M.2 Solid State Hard Drive:
Quantity: $2735
Add to Cart

Typically in stock for shipment in 3-4 weeks. Subject to global supply chain challenges.

UEINet-SIM

The UEINet chassis provides ultra-compact Ethernet based I/O module suitable for a wide variety of distributed data acquisition, control and SCADA applications. Based on UEI's popular PowerDNA® Cube architecture, the new series is designed for applications requiring distributed I/O with a very small footprint.

The UEINet chassis is an extremely rugged, Gigabit Ethernet-based I/O interface. The wide variety of allows you to configure one or more cubes to match the specific I/O requirements of your application. The PowerDNA Cube is ideally suited for a wide variety of industrial, aerospace and laboratory data acquisition and control applications.

UEINet chassis are 2.7" x 4.1" x 4" and are packed with power and flexibility. Each UEINet module consists of two primary subsections: a Core Module and and an I/O board.

The “standard" UEINet is designed to run as a slave I/O unit controlled directly by a host PC. The UEINet PAC UPG option allows the unit to run as a stand-alone device running an application you write in either Linux or VxWorks operating systems. Simulink users can use the UEINet SIM UPG option to enable the ability to build applications in Simulink. These Simulink modules may be run on a host PC, stand-alone on the UEINet, or in a SCADA mode where a stand-alone application runs, but can be tuned by the host PC. Finally, there the UEINet Mod UPG allows the UEINet to run as a MODBUS TCP node and UEINet OPC-UA UPG.

The Core Module occupies the top portion of the chassis and provides two independent Gigabit Ethernet Network Interface Controllers (NICs) with separate IP addresses. These may be configured as a control port and a diagnostic port or they may be teamed/bonded to allow redundant network access. The control port is the primary interface from the host PC. The diagnostics port allows other computers (or a different thread on the host) to interrogate the I/O and system status of the Cube.

The Core module also provides provides the 8347 series PowerPC CPU, two USB 2.0 controller ports (active only with the UEIPAC option), indicator lights, timing/trigger interface, configuration ports and internal power supply. It's the brains of the UEINet and controls the unit's operations including the interface with the host Controller (and other Cubes), acting as the primary processor in stand alone deployments as well as supervising the activity of the I/O board.

The remainder of the chassis contains the I/O board. A custom (though fully COTS) I/O configuration is possible by specifying the UEINet with any of UEI's DNA-series I/O boards. An overview of these board is also provided on the following pages, while detailed specifications can be obtained from the various I/O boards' datasheets. With over 60 different I/O boards available we're sure to have just what your application requires.

The UEINet-FLANGE, mounting option allows the UEINet series to be easily mounted to any flat surface. The UEINet-DR, DIN rail mount allows the unit to be mounted to any standard 35 mm DIN rail.

Related Media

How to Build a Simulink Model for UEISIM

See how to build a Simulink model using United Electronic Industries' UEISIM library.

How to deploy your SIMULINK model on UEI Hardware

In this video, we will build a Simulink model and deploy it on our data acquisition and control hardware (UEISIM).

Control/Monitoring options for your model on UEI Hardware - Part 2

Independent monitoring and control via .NET, LabVIEW, Simulink, and an internet browser. UEISIM.

Control/Monitoring options for your model on UEI Hardware - Part 1

See how to decouple your model from the Mathworks Simulink environment for stand alone operation using web sockets or TCP/IP. UEISIM.

UEI Technical Master Class: Keep Your Vehicle Deployment On Course

In this UEI Master Class, engineers from UEI, Mathworks, and Real-Time Innovations (RTI) discuss how Model-Based design is transforming the way engineers and scientists plan, build, and test their systems.

Using RTI to Share Data Among Control Models

UEI hardware and RTI provides a flexible, robust way for you to share information and data amongst networked control systems and hardware. In this video we demonstrate how easy it is to set up an iDDS system and explain it can work for your application.